-
Leeson Washguard
leeson-washguard
-
Leeson Single Phase TEFC Rigid Base Washguard Motors
- White Epoxy
- Single Phase & DC
- TEFC
- Rigid Base
Enhanced performance in wet, humid areas- Our original moisture-shedding "duck" motor
- Durable RUST-OLEUM® white epoxy coating
- Stainless steel shaft, conduit box cover, nameplate, fan guard
- Special gaskets, slingers and seals
- Four endshield drains
- Moisture-resistant interior components
- IRIS™ insulation system
- Single-phase, three-phase and DC SCR models
- Meets IP55 enclosure protection
- Three phase motors are suitable for use on VFDs
- 10:1 ratio for constant or variable torque at 1.0 SF
-
Leeson Single Phase TEFC C Face Less Base Washguard Motors
- White Epoxy
- Single Phase & DC
- TEFC
- C Face Less Base
Enhanced performance in wet, humid areas- Our original moisture-shedding "duck" motor
- Durable RUST-OLEUM® white epoxy coating
- Stainless steel shaft, conduit box cover, nameplate, fan guard
- Special gaskets, slingers and seals
- Four endshield drains
- Moisture-resistant interior components
- IRIS™ insulation system
- Single-phase, three-phase and DC SCR models
- Meets IP55 enclosure protection
- Three phase motors are suitable for use on VFDs
- 10:1 ratio for constant or variable torque at 1.0 SF
-
Leeson TENV C Face with Removable Base Washguard DC Motors
- White Epoxy
- Single Phase & DC
- SCR Rated 90 & 180 Volts
- Our original moisture-shedding "duck" motor
- Durable RUST-OLEUM® white epoxy coating
- Stainless steel shaft, conduit box cover, nameplate, fan guard
- Special gaskets, slingers and seals
- Four endshield drains
- Moisture-resistant interior components
- IRIS™ insulation system
- Single-phase, three-phase and DC SCR models
- Meets IP55 enclosure protection
- Three phase motors are suitable for use on VFDs
- 10:1 ratio for constant or variable torque at 1.0 SF
-
Leeson Single Phase TEFC C Face with Base Washguard Motors
- White Epoxy
- Single Phase & DC
- TEFC
- C Face With Base
Featuring Electronic Solid State Encapsulated Switch
Enhanced performance in wet, humid areas- Our original moisture-shedding "duck" motor
- Durable RUST-OLEUM® white epoxy coating
- Stainless steel shaft, conduit box cover, nameplate, fan guard
- Special gaskets, slingers and seals
- Four endshield drains
- Moisture-resistant interior components
- IRIS™ insulation system
- Single-phase, three-phase and DC SCR models
- Meets IP55 enclosure protection
- Three phase motors are suitable for use on VFDs
- 10:1 ratio for constant or variable torque at 1.0 SF
-
Leeson Three Phase TENV and TEFC C Face Less Base Washguard Motors
- White Epoxy
- Three Phase
- TENV and TEFC C Face Less Base
-
Leeson Three Phase TENV and TEFC C Face with Base Washguard Motors
- White Epoxy
- Three Phase
- TENV and TEFC C Face with Base
-
Leeson Three Phase TEFC Rigid Base Washguard Motors
- White Epoxy
- Three Phase
- TEFC
- Rigid Base
-
Leeson Three Phase 575 Volts TEFC C Face with Base Washguard Motors
- White Epoxy
- Three Phase
- 575 Volts
- TEFC
- C Face with Base
-
Leeson Three Phase TEFC JM Pump Washguard Motors
- White Epoxy
- Three Phase & Brakekits™
- TEFC
- JM Pump
-
Leeson Three Phase TEFC C Face Less Base Jet Pump Washguard Motors
- White Epoxy
- Three Phase & Brakekits™
- JET Pump
- Threaded Shaft
- TEFC
- C-face Less Base
-
Leeson Three Phase TEFC C Face with Base Jet Pump Washguard Motors
- White Epoxy
- Three Phase & Brakekits™
- JET Pump
- Threaded Shaft
- TEFC
- C-face with Base
-
Leeson TENV/TEFC C Face with Base Washguard Motor
- White Epoxy
- Three Phase & Brakekits™
- TENV/TEFC
- C Face with Base
-
Leeson TENV/TEFC C Face Less Base Washguard Motor
- White Epoxy
- Three Phase & Brakekits™
- TENV/TEFC
- C Face less Base
-
Leeson Stainless Frame TENV C Face Less Base Washguard II Motors
- Stainless Frame
- Three Phase
- TENV
- C Face Less Base
Superior, extended life in severe environments- Paint-free exterior - stainless frame and conduit box lid, specially processed endshields and conduit box housing
- Etched stainless steel nameplate
- Proven WASHGUARD mechanical and electrical features
- IRIS™ insulation system
- BISSC certified for baking industry
- Meets IP55 enclosure protection
- Three phase motors are suitable for use on VFDs
- 10:1 ratio for constant or variable torque at 1.0 SF
LEESON Severe Duty, stainless frame, WASHGUARD II motors are designed for superior extended service in severe environments. Typical applications include food processing areas requiring frequent sanitation procedures using high pressure cleaning with concentrated caustic solutions, areas of high humidity and in chemical environments.
Standards and Approvals
UL component recognized, file number E57948, guide number PRGY2. Energy efficiency ratings are verified by an independent testing laboratory. CSA Energy Efficiency Verification Program, report number EEV 78720-1. Construction is CSA Certified for safety report number LR33543. WASHGUARD II motors are certified to the Baking Industry Sanitation Standard #29 and listed under BISSC authorization number 769. -
Leeson Stainless Frame TENV C Face with Base Washguard II Motors
- Stainless Frame
- Three Phase
- TENV
- C Face with Base
Superior, extended life in severe environments- Paint-free exterior - stainless frame and conduit box lid, specially processed endshields and conduit box housing
- Etched stainless steel nameplate
- Proven WASHGUARD mechanical and electrical features
- IRIS™ insulation system
- BISSC certified for baking industry
- Meets IP55 enclosure protection
- Three phase motors are suitable for use on VFDs
- 10:1 ratio for constant or variable torque at 1.0 SF
LEESON Severe Duty, stainless frame, WASHGUARD II motors are designed for superior extended service in severe environments. Typical applications include food processing areas requiring frequent sanitation procedures using high pressure cleaning with concentrated caustic solutions, areas of high humidity and in chemical environments.
.Standards and Approvals
UL component recognized, file number E57948, guide number PRGY2. Energy efficiency ratings are verified by an independent testing laboratory. CSA Energy Efficiency Verification Program, report number EEV 78720-1. Construction is CSA Certified for safety report number LR33543. WASHGUARD II motors are certified to the Baking Industry Sanitation Standard #29 and listed under BISSC authorization number 769. -
Leeson Three Phase TENV/TEFC C Face with Base Washguard All-stainless SST Motors
- Washguard SST
- All-stainless
- Three-phase
- TENV/TEFC
- C Face with Base
Stainless Steel Tough for demanding washdown applications- All exterior components of 300 series stainless steel, including motor frame, endshield and conduit box castings
- Moisture resistant sealant between frame and endbells
- Full-fact nameplate is laser-etched on the motor frame
- Built to withstand the demanding washdown environments found in the food processing, chemical processing and beverage industries
- No paint or coatings of any type used on the exterior of the motor
- Four locations for T-drains provided on each endshield
- IRIS™ insulation system
- Meets IP55 enclosure protection
- Three phase motors are suitable use on VFDs
- 10:1 ratio for constant or variable torque at 1.0 SF
Mechanical Protection Features:
All exterior components - frame, base, endshields, fan guard, shaft, hardware, conduit box and cover - are made from 300 series stainless steel for maximum corrosion resistance. Nameplate data is permanently laser-etched into the motor frame - no Mylar nameplate that can wash off or riveted metal nameplate to trap dirt. No paint or any type of coating is used on the exterior of the motor. Sealant is applied to endshield and frame fits before assembly to prevent water entry. Shaft seals on both ends of TEFC motors - shaft end only on TENV. Double-sealed bearings have high performance Exxon Polyrex EM grease. Conduit box is fully gasketed half-split design with flanged cover and body gasket with lead separator. Anticorrosion coating on rotor prevents corrosion. Four quadrant drain locations on each endbell allow drainage of condensation in any mounting position. Stainless steel T-drains are provided to prevent liquids from splashing into the drain locations. Motors are shipped with a T-drain assembled in the six o'clock position on the opposite endshield. Another T-drain is shipped loose in the conduit box for installation at the lowest point of the shaft-end endshield. For a totally sealed motor, a spare pipe plug is included to replace the pre-installed T-drain. Mechanical performance is further enhanced by over-sized bearings, heavy 12 gauge base, shaft-end bearing is locked internally to limit axial endplay, and specially designed shaft extension resists breakage at bearing journal.
Electrical Performance and Protection Features:
FHP Washguard SST full load efficiencies meet EPACT standards for non-exempt motors when tested without shaft seals. For extra moisture resistance, windings are immersed and cured in polyester insulating varnish. LEESON’s exclusive IRIS™ Inverter-Rated Insulation System provides extra protection and long life, especially in inverter driven applications. 20:1 Constant Torque Operation
Standards and Approvals:
UL component recognized, file number E57948, guide number PRGY2. Energy efficiency ratings are verified by an independent testing laboratory. CSA Energy Efficiency Verification Program, report number EEV 78720-1.
Construction is CSA Certified for safety report number LR33543. Motor is CE marked for European acceptance. -
Leeson Single Phase TENV/TEFC C Face with Base Washguard All-stainless SST Motors
- Washguard SST
- All-stainless
- Single-phase
- TENV/TEFC
- C Face with Base
Stainless Steel Tough for demanding washdown applications- All exterior components of 300 series stainless steel, including motor frame, endshield and conduit box castings
- Moisture resistant sealant between frame and endbells
- Full-fact nameplate is laser-etched on the motor frame
- Built to withstand the demanding washdown environments found in the food processing, chemical processing and beverage industries
- No paint or coatings of any type used on the exterior of the motor
- Four locations for T-drains provided on each endshield
- IRIS™ insulation system
- Meets IP55 enclosure protection
- Three phase motors are suitable use on VFDs
- 10:1 ratio for constant or variable torque at 1.0 SF
Mechanical Protection Features:
All exterior components - frame, base, endshields, fan guard, shaft, hardware, conduit box and cover - are made from 300 series stainless steel for maximum corrosion resistance. Nameplate data is permanently laser-etched into the motor frame - no Mylar nameplate that can wash off or riveted metal nameplate to trap dirt. No paint or any type of coating is used on the exterior of the motor. Sealant is applied to endshield and frame fits before assembly to prevent water entry. Shaft seals on both ends of TEFC motors - shaft end only on TENV. Double-sealed bearings have high performance Exxon Polyrex EM grease. Conduit box is fully gasketed half-split design with flanged cover and body gasket with lead separator. Anticorrosion coating on rotor prevents corrosion. Four quadrant drain locations on each endbell allow drainage of condensation in any mounting position. Stainless steel T-drains are provided to prevent liquids from splashing into the drain locations. Motors are shipped with a T-drain assembled in the six o'clock position on the opposite endshield. Another T-drain is shipped loose in the conduit box for installation at the lowest point of the shaft-end endshield. For a totally sealed motor, a spare pipe plug is included to replace the pre-installed T-drain. Mechanical performance is further enhanced by over-sized bearings, heavy 12 gauge base, shaft-end bearing is locked internally to limit axial endplay, and specially designed shaft extension resists breakage at bearing journal.
Electrical Performance and Protection Features:
FHP Washguard SST full load efficiencies meet EPACT standards for non-exempt motors when tested without shaft seals. For extra moisture resistance, windings are immersed and cured in polyester insulating varnish. LEESON’s exclusive IRIS™ Inverter-Rated Insulation System provides extra protection and long life, especially in inverter driven applications. 20:1 Constant Torque Operation
Standards and Approvals:
UL component recognized, file number E57948, guide number PRGY2. Energy efficiency ratings are verified by an independent testing laboratory. CSA Energy Efficiency Verification Program, report number EEV 78720-1.
Construction is CSA Certified for safety report number LR33543. Motor is CE marked for European acceptance. -
Leeson Three Phase TENV/TEFC C Face Less Base Washguard All-stainless SST Motors
- Washguard SST
- All-stainless
- Three-phase
- TENV/TEFC
- C Face less Base
Stainless Steel Tough for demanding washdown applications- All exterior components of 300 series stainless steel, including motor frame, endshield and conduit box castings
- Moisture resistant sealant between frame and endbells
- Full-fact nameplate is laser-etched on the motor frame
- Built to withstand the demanding washdown environments found in the food processing, chemical processing and beverage industries
- No paint or coatings of any type used on the exterior of the motor
- Four locations for T-drains provided on each endshield
- IRIS™ insulation system
- Meets IP55 enclosure protection
- Three phase motors are suitable use on VFDs
- 10:1 ratio for constant or variable torque at 1.0 SF
Mechanical Protection Features:
All exterior components - frame, base, endshields, fan guard, shaft, hardware, conduit box and cover - are made from 300 series stainless steel for maximum corrosion resistance. Nameplate data is permanently laser-etched into the motor frame - no Mylar nameplate that can wash off or riveted metal nameplate to trap dirt. No paint or any type of coating is used on the exterior of the motor. Sealant is applied to endshield and frame fits before assembly to prevent water entry. Shaft seals on both ends of TEFC motors - shaft end only on TENV. Double-sealed bearings have high performance Exxon Polyrex EM grease. Conduit box is fully gasketed half-split design with flanged cover and body gasket with lead separator. Anticorrosion coating on rotor prevents corrosion. Four quadrant drain locations on each endbell allow drainage of condensation in any mounting position. Stainless steel T-drains are provided to prevent liquids from splashing into the drain locations. Motors are shipped with a T-drain assembled in the six o'clock position on the opposite endshield. Another T-drain is shipped loose in the conduit box for installation at the lowest point of the shaft-end endshield. For a totally sealed motor, a spare pipe plug is included to replace the pre-installed T-drain. Mechanical performance is further enhanced by over-sized bearings, heavy 12 gauge base, shaft-end bearing is locked internally to limit axial endplay, and specially designed shaft extension resists breakage at bearing journal.
Electrical Performance and Protection Features:
FHP Washguard SST full load efficiencies meet EPACT standards for non-exempt motors when tested without shaft seals. For extra moisture resistance, windings are immersed and cured in polyester insulating varnish. LEESON’s exclusive IRIS™ Inverter-Rated Insulation System provides extra protection and long life, especially in inverter driven applications. 20:1 Constant Torque Operation
Standards and Approvals:
UL component recognized, file number E57948, guide number PRGY2. Energy efficiency ratings are verified by an independent testing laboratory. CSA Energy Efficiency Verification Program, report number EEV 78720-1.
Construction is CSA Certified for safety report number LR33543. Motor is CE marked for European acceptance. -
Leeson Three Phase TENV/TEFC C Face with Base Washguard All-Stainless SSD Motors
- Premium Stainless Steel Duck
- All Stainless
- Three Phase
- TENV/TEFC
- C Face with Base
Maximum service in critically clean or corrosive environments- All exterior components of stainless steel
- Endshields o-ring sealed to frame
- IEEE 841 severe-duty features standard
- Meets demanding pharmaceutical requirements, also excellent for chemical-processing applications
- Meets IP56 enclosure protection
- Incorporates all WASHGUARD mechanical and electrical features, plus IRIS™ insulation system
- IRIS™ insulation system
- BISSC certified for baking industry
-
Leeson Three Phase TENV/TEFC C Face Less Base Washguard All-Stainless SSD Motors
Premium Stainless Steel Duck
- All Stainless
- Three Phase
- TENV/TEFC
- C Face less Base
Maximum service in critically clean or corrosive environments- All exterior components of stainless steel
- Endshields o-ring sealed to frame
- IEEE 841 severe-duty features standard
- Meets demanding pharmaceutical requirements, also excellent for chemical-processing applications
- Meets IP56 enclosure protection
- Incorporates all WASHGUARD mechanical and electrical features, plus IRIS™ insulation system
- IRIS™ insulation system
- BISSC certified for baking industry
-
Leeson Single Phase TENV/TEFC C Face with Base Washguard All-Stainless SSD Motors
Premium Stainless Steel Duck
- All Stainless
- Single Phase
- TENV/TEFC
- C Face with Base
Maximum service in critically clean or corrosive environments- All exterior components of stainless steel
- Endshields o-ring sealed to frame
- IEEE 841 severe-duty features standard
- Meets demanding pharmaceutical requirements, also excellent for chemical-processing applications
- Meets IP56 enclosure protection
- Incorporates all WASHGUARD mechanical and electrical features, plus IRIS™ insulation system
- IRIS™ insulation system
- BISSC certified for baking industry
-
Leeson Single Phase TENV/TEFC C Face Less Base Washguard All-Stainless SSD Motors
Premium Stainless Steel Duck
- All Stainless
- Single Phase
- TENV/TEFC
- C Face less Base
Maximum service in critically clean or corrosive environments- All exterior components of stainless steel
- Endshields o-ring sealed to frame
- IEEE 841 severe-duty features standard
- Meets demanding pharmaceutical requirements, also excellent for chemical-processing applications
- Meets IP56 enclosure protection
- Incorporates all WASHGUARD mechanical and electrical features, plus IRIS™ insulation system
- IRIS™ insulation system
- BISSC certified for baking industry
-
Leeson Brake Motor Three Phase TENV C Face with Base Washguard All-Stainless SSD Motors
Premium Stainless Steel Duck
- All Stainless
- Three Phase
- TENV
- C Face with Base
Maximum service in critically clean or corrosive environments- All exterior components of stainless steel
- Endshields o-ring sealed to frame
- IEEE 841 severe-duty features standard
- Meets demanding pharmaceutical requirements, also excellent for chemical-processing applications
- Meets IP56 enclosure protection
- Incorporates all WASHGUARD mechanical and electrical features, plus IRIS™ insulation system
- IRIS™ insulation system
- BISSC certified for baking industry.
-
Leeson Three Phase TEFC JM Pump Washguard All-Stainless SSD Motors
- Premium Stainless Steel Duck
- All Stainless
- Three Phase
- TEFC
- JM Pump
- All exterior components of stainless steel
- Endshields o-ring sealed to frame
- IEEE 841 severe-duty features standard
- Meets demanding pharmaceutical requirements, also excellent for chemical-processing applications
- Meets IP56 enclosure protection
- Incorporates all WASHGUARD mechanical and electrical features, plus IRIS™ insulation system
- IRIS™ insulation system
- BISSC certified for baking industry
